Ultra jet makeover

J

JPT

Member
Did some more work on the floor tonight, made a little progress.  Still have to remove the old carpet glue in areas,  it's A MAJOR PAIN IN THE A$$!  But its looking good so far.  Researching options on covering the black areas with a carbon fiber or something else.  who knows
 
J

JPT

Member
A little update on my Ultra.  Got all the carpet out and floors cleaned up.  Pulled the gas tanks out, drained old fuel out and cleaned them up.  The straps that hold the tanks in place had come loose from the hull, so their being taken care of now.  Also got all the anodised pieces back from Atlas, puting them back on as I go along with new polished hardware.
 
Knotty Girl

Knotty Girl

New member
JPT said:
A little update on my Ultra.  Got all the carpet out and floors cleaned up.  Pulled the gas tanks out, drained old fuel out and cleaned them up.  The straps that hold the tanks in place had come loose from the hull, so their being taken care of now.  Also got all the anodised pieces back from Atlas, puting them back on as I go along with new polished hardware.
Click to expand...

Looks good where is Atlas?  I need a few pieces done.
 
J

JPT

Member
Its on the north side of hst. off of 45 just past the 610 loop. 8303 Bauman rd, Houston Tx 77022.
I dealt with Alex, the manager, he's a good guy.
 
Knotty Girl

Knotty Girl

New member
JPT said:
Its on the north side of hst. off of 45 just past the 610 loop. 8303 Bauman rd, Houston Tx 77022.
I dealt with Alex, the manager, he's a good guy.
Click to expand...

TKS I'll give him a call.
 
J

JPT

Member
Still waiting on Bds to finish the blower and get it shipped.  In the mean time still tinkering with the rigging n such.  Putting new polished AN fittings on all the lines.  Its a box full of work

 
J

JPT

Member
Got some more parts in today.  Second box of AN fittings and hose, also got my headers back from JET-HOT.  Had the guys over there ceramic coat them for me and they turned out great.
 
J

jdeaton

New member
Did the coating people say anything about breaking your headers in.  I found out, after the fact, that there is a proper way, just don't remember what the process was. think.gif
 
J

JPT

Member
Well finally got my engine back from KPE, complete rebuild with new stuff and different stuff.  Dyno'd 794hp at 5800rpm, 16% under driven w/ 4.6lbs boost. BDS 8-71 blower, Teague super chiller, bored .030" over to 509ci, Manley H-beam rods, SRP blower pistons, Clevite Hell fire file fit rings, Comp cams hydraulic roller cam, Manley severe duty marine valves-dual springs-retainers-locks, MSD billet distributor, MSD high vibration coil, Moroso ultra wires, ATI balancer, Miziere Billet Flexplate, Chrome plated 10qrt pan, chrome coil mount, new puke tank, valve covers w/ -12an welded on, and the coated headers will be bolted up too.  Waiting on header gaskets and a few more fittings that should be weds, then I can finish the loose ends.  ALMOST READY AND IT"S ABOUT TIME!!!!

being dyno'ed
2hs25ax.jpg


at the house
mwz05c.jpg


back in the boat
3011shl.jpg

 
J

JPT

Member
Well I've had the engine in the boat now for a few weeks?? and did all the tinkering, plumbing, test'n'tunin in the driveway.  Took it out a few times to find any unseen issues.  A few oil leaks here n there, fixed now.  Waiting on the seamstress to finish modifying the cover so it'll fit again.  Was able to get INSURANCE on it too! Gonna go through the trailer wheel bearings, noticed a seal leaking and slinging grease, make sure it's road trip ready.  I'll get the lil things taken care of and be ready to see you guys at Tawakoni 
 
You must log in or register to reply here.
Top