Old Buck's Project "Mini Me"

[oldbuck40]

:smile15:

Looks great Greg.........so when do I get to drive it???? :smile13:

Based on the speed of his finishing past projects I'd say: your daughter will be old enough to drive it when it finally hits the water!!!!!  :smile17: :smile23:

lol you better think again! :smile23: :smile23: :smile23:

 

[NotImportant-1]

:smile15:

Looks great Greg.........so when do I get to drive it???? :smile13:

Based on the speed of his finishing past projects I'd say: your daughter will be old enough to drive it when it finally hits the water!!!!!  :smile17: :smile23:

Awwwwwwwwwwwwwwwwwwwwwwwwwwwwwww Shit

Get up Greg

Come on buddy



Wake up


TJ didn't mean to knock you the "F" out oldman


:smile23: :smile23: :smile23: :smile23: :smile23:

 

[NotImportant-1]

Better watch out Jeff


The oldman will get his pink crayons out again and write some more GAY hate mail


LOL

 

[oldbuck40]

Better watch out Jeff


The oldman will get his pink crayons out again and write some more GAY hate mail


LOL

:smile23: :smile23: :smile23: :smile23: :smile23: :smile23: :smile23: :smile23: :smile23: :smile23:

 

[TexasJet]

Better watch out Jeff


The oldman will get his pink crayons out again and write some more GAY hate mail


LOL

Ya, I'm sure I will pay for that post sooner or later. Probably sooner, like next weekend. :evil: :grin:

 

[turbo]

That looks awesome!  Woulda been kinda cool to fiberglass a fake blower into the top with zoomies coming out the side of the hump.. 
    anyway, looks great!  :smile15:

 

[big daddy custom boats]

seen on of these boats on craigslist in houston! kinda cool! :smile13:

 

[pro53]

You got it home yet Greg? :grin:

 

[oldbuck40]

You got it home yet Greg? :grin:

nope! not yet. both should be ready to pick up next week sometime! :smile15:

 

[oldbuck40]

well i got the diverter put back together!

[attachment deleted by admin]

 

[oldbuck40]

had to shave the front part of the suction housing down a bit on the funjet! it hung down below the keel bout 1/8 inch and figured it would probably cause it to suck a little air!

this is a picture of a pump on a wetbike but you can get the idea! the intake and the 90 degree gearbox are one piece and just bolts to the floor like a intake in a larger boat,,,BUT the casting let the intake hang down lower in the front when it should be flush.

Geeze so much off the wall crap i gotta fix on this little sucker! :smile23: :smile23: :smile23:

[attachment deleted by admin]

 

[oldbuck40]

Kenny here is a good shot that shows where the pipes go! (bottom 2 holes either side of the pump hole)

[attachment deleted by admin]

 

[Devilman]

Four banger with twice-pipes, nice...... lol  :grin:

 

[oldbuck40]

Four banger with twice-pipes, nice...... lol  :grin:

:smile23: :smile23: :smile23: like this!

[attachment deleted by admin]

 

[Devilman]

I saw that a little bit ago, thats pretty cool. Bet it sounds ungodly. :smile15: Thats what you need... :grin:

 

[oldbuck40]

Slowly but surely pluggin along getting things fitted, cleaning the threads out with a tap is taking alot of time but its coming along.
i set the pump up with just a couple of bolts to prefit everything before i start the permanent install. tight now we are getting ready to install the stainless exhaust tip's. they should stick out each side of the pump bout 6 inches and turn out and down at a 45 degree angle.  then i gotta build another ride plate! the other one was pretty bent up.

[attachment deleted by admin]

 

[pro53]

Hey Greg, I would try it without it first. The way that thing sticks out it might not need it  :grin: When you tow you might have to hang a red flag off it  :grin:

 

[oldbuck40]

Hey Greg, I would try it without it first. The way that thing sticks out it might not need it  :grin: When you tow you might have to hang a red flag off it  :grin:

:smile23: :smile23: :smile23: hell its only 2 ft! 

 

[Devilman]

Is there much difference in nozzle size from the original to the diverter you added to it? Looks quite a bit bigger, don't guess it'll affect it any?

 

[oldbuck40]

Is there much difference in nozzle size from the original to the diverter you added to it? Looks quite a bit bigger, don't guess it'll affect it any?

Actually i havent measured, but eyeballing it the smallest area in the diverter is maybe a half inch smaller than the original hole in the bowl. if anything it should help it.