As most of you know, I had to give up boating because of my back problems. Anyway I sold both my boats, leaving me with some parts I have no use for. Here's some pictures, if you see something you might need, give me a call. Chevrolet Rewarder headers, Lines and braces. Ford Valve covers, Exhaust Logs are Chevrolet. starter ring Chevy, Pistons TRW high compression with steel H beam rods, roller rockers, etc. Call I'll give you as much information as I can. (979-451-3609) Jim
Last Boat Garage Sale
- Thread starter jdeaton
- Start date
horsepower junkie
New member
Is that new timing set for BBCif so I'll take it and the rockers if fhey haven't sold yet and also the siingle grove pulley call at 361-701-9986
ChryslerJet
New member
Jim how much for that carter/edelbrock carb and what size is it? I think it might work well on the CJ's motor. Also let me know on the Holley's as well for the Carlson's 440.
Here's the deal on my parts. I have offered a package deal to a couple of guys on the THB boards. I'm suppose to know later today if they are going to buy it all (as a lot) for $930.00 (Don't asked how I came up with that price).
Don the remote oil filter has the block adapters for both a Ford and a Chevy. Priced at $50.00 for everything.
Chris the Edelbrock is an 850, it was on the Chevelle I bought and was too much gas for that motor. The other Holley's range from 600 to 750 double pumpers. I can get the specifics if you need (I.E. part numbers) I'll take $240.00 for all 4 carburetors.
Right now everything is considered sold, but I will know more by the end of the day.
Is this post confusing or what. think.gif
Don the remote oil filter has the block adapters for both a Ford and a Chevy. Priced at $50.00 for everything.
Chris the Edelbrock is an 850, it was on the Chevelle I bought and was too much gas for that motor. The other Holley's range from 600 to 750 double pumpers. I can get the specifics if you need (I.E. part numbers) I'll take $240.00 for all 4 carburetors.
Right now everything is considered sold, but I will know more by the end of the day.
Is this post confusing or what. think.gif
Just received PM that the parts are up for grabs. So I'm selling them individually.
FL 350 I don't know what brand the roller rockers are, but they are the standard ratio for a Big Block Chevy. They aren't stamped anywhere. Is there a way I can measure them to find the ratio?
FL 350 I don't know what brand the roller rockers are, but they are the standard ratio for a Big Block Chevy. They aren't stamped anywhere. Is there a way I can measure them to find the ratio?
ChryslerJet
New member
DiamondJim said:
Jim consider the carbs sold. Will get with you on when to pick them up.
HammerDown
New member
Details on the chute jacket please
Timing sets, Scoop Tray, Rockers, single grove aluminum pulley, dual oil filter system, oil drain kit, Ford Motorsport valve covers and all carburetors are gone. Waiting on money.
The Jacket is a Simpson Life line Chute jacket, has been well taken care of, obviously stored inside. Leg straps, harness and covering in excellent condition, no tears or repairs. No marking on size, but I'm 5' 11" and weigh 195. and it fits me like a glove. I wear a Large size in a sports jacket. If it's to tight you will need to get the Zipper extension from Simpson. I'm asking $300.00
The Jacket is a Simpson Life line Chute jacket, has been well taken care of, obviously stored inside. Leg straps, harness and covering in excellent condition, no tears or repairs. No marking on size, but I'm 5' 11" and weigh 195. and it fits me like a glove. I wear a Large size in a sports jacket. If it's to tight you will need to get the Zipper extension from Simpson. I'm asking $300.00
73 Sanger Flat
Active member
Does the starter fit a 168 tooth flywheel ?